Stage Ape Lighting Stage Ape Lighting

The Lighting you need... at Prices you'll go APE over...


Home

stage ape lighting
     Contact Us:  
     
stage ape
stage ape The Ape PAR 38 LED 86... stage ape
Short, Black LED PAR 38 Can with 86 5mm LED's and a 35 Degree Beam Angle...

This LED PAR 38 can puts out 1,277 LUX at 1 meter. (A standard PAR 38 can with a 150 watt incandescent bulb and a primary blue color gel in front of it puts out 99 Lux at 1 meter).

44 red, 21 green, 21 blue LED’s.

Soft edge spot. Built in mic.

5 channel dmx: #1=on/off and strobe, #2=dimmer, #3=Red #4=Green #5=Blue

Stand alone modes features: Sound active with built in mic and sensitivity knob, auto color change and master/slave mode.

Color temp less than 6000k. Includes 1 amp short fuse, 100,000 hour LED’s. Under 13 watt current draw.

Size 4.75" x 4.75" x 3.5" and weighs 1.7Lbs
 LED-86
stage ape Click Here To Purchase stage ape

Instructions for STAND ALONE operation:

**These LED lights can produce many different effects and colors without using a controller. Just use the dip switches on the rear of the light to mix the colors to produce brilliant shades of purple, pink, magenta and more. Each light has multiple  dip switches for each color. Make each color combinations your own to fit your event or show.** 		LED-86
With only dip switch #1 on (up), the Red LED's come on at approximately 50%

With only dip switch #2 on (up), the Red LED's come on at approximately 50%

With only dip switch #1 & #2 on (up), the Red LED's come on at approximately 100%

With only dip switch #3 on (up), the Green LED's come on at approximately 50%

With only dip switch #4 on (up), the Green LED's come on at approximately 50%

With only dip switch #3 & #4 on (up), the Green LED's come on at approximately 100%

With only dip switch #5 on (up), the Blue LED's come on at approximately 50%

With only dip switch #6 on (up), the Blue LED's come on at approximately 50%

With only dip switch #5 & #6 on (up), the Blue LED's come on at approximately 100% 		 LED-86
With only dip switch #9 on (up), full brightness, fast color change.

With only dip switch #9 & #7 on (up), full brightness, slow color change.

With only dip switch #8 on (up), full brightness, sound active color change.		 LED-86
DMX mode:

The 120-LED-86 is a 5 channel dmx light so you start DMX value 1. Set dip switches #1 & # 10 on the first fixture to the on position. Dip switch 10 is on to tell the light it is in DMX mode and does not have a value. This will allow the first 5 sliders on your controller to control the first light.  So now set the next fixture at dmx value 6 which is dip switches #2 & #3 & #10 to the on position. This will allow you to us sliders 6 through 10 to control the second fixture.

On your DMX controller:
Slider #1 is:
    0-15 = Off
    16-79 = Strobe, slow to fast
    80-159= Pulse strobe (fades out and back to bright, slow to fast)
    160-255 = On
Slider #2- Brightness, low to high (controls overall brightness).
Slider #3- Brightness of the red LED’s
Slider #4- Brightness of the green LED’s
Slider #5- Brightness of the blue LED’s

How to use this light with the American DJ MyDMX software		 LED-86

Master/Slave:


Set dip switches #1-8 on the master fixture to the "On" position. Connect the second fixture by DMX cord.
Then set dip switch #10 of the slave fixture to the "On" position. 

CORD

Click Here To Purchase

Back


 Copyright © 2009 by Stage Ape Lighting